SPN 1188 - FMI 3 (Fault Code 465)
Friday, July 06, 2018
Fault Codes CUMMINS GTA38 K38 K50 QSK38 QSK50/60 CM850,
Fault Codes CUMMINS Signature ISX QSX15 CM570
SPN1188 FMI3
Turbocharger 1 Wastegate Control Circuit - Voltage Above Normal or Shorted to High Source
CODES:
Fault Code: 465
PID(P), SID(S): S32
SPN: 1188
FMI: 3/3
Lamp: Amber
REASON: High voltage detected at the wastegate actuator number 1 circuit.
EFFECT: Engine power derate.
Circuit Description:
The wastegate actuators are devices used by the Engine Control Module(ECM) to control boost pressure.
Component Location:
The wastegate controller is located on the air inlet horn.
Conditions for Running the Diagnostics:
This diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.
Conditions for Setting the Fault Codes:
The Engine Control Module (ECM) detected the wastegate actuator circuit voltage was out of range high.
Action Taken When the Fault Code is Active:
• The ECM illuminates the amber CHECK ENGINE lamp immediately when the diagnostic runs and fails.
Conditions for Clearing the Fault Code:
• To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
• Use the recommended Cummins® electronic service tool or equivalent to verify the fault code is inactive.
• The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
• The “Reset All Faults” command in the recommended Cummins® electronic service tool or equivalent can be used to clear active and inactive faults.
Shop Talk:
Possible cause of this fault code:
• Open circuit in the engine harness, connectors, or actuator.
• Signal circuit shorted to voltage source.
Read More:
SPN 94 - FMI 18 (Fault Code 482)
SPN 1188 - FMI 4 (Fault Code 466)
Blog.Teknisi
Turbocharger 1 Wastegate Control Circuit - Voltage Above Normal or Shorted to High Source
 |
| Wastegate Actuator |
CODES:
Fault Code: 465
PID(P), SID(S): S32
SPN: 1188
FMI: 3/3
Lamp: Amber
REASON: High voltage detected at the wastegate actuator number 1 circuit.
EFFECT: Engine power derate.
Circuit Description:
The wastegate actuators are devices used by the Engine Control Module(ECM) to control boost pressure.
Component Location:
The wastegate controller is located on the air inlet horn.
Conditions for Running the Diagnostics:
This diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.
Conditions for Setting the Fault Codes:
The Engine Control Module (ECM) detected the wastegate actuator circuit voltage was out of range high.
Action Taken When the Fault Code is Active:
• The ECM illuminates the amber CHECK ENGINE lamp immediately when the diagnostic runs and fails.
Conditions for Clearing the Fault Code:
• To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
• Use the recommended Cummins® electronic service tool or equivalent to verify the fault code is inactive.
• The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
• The “Reset All Faults” command in the recommended Cummins® electronic service tool or equivalent can be used to clear active and inactive faults.
Shop Talk:
Possible cause of this fault code:
• Open circuit in the engine harness, connectors, or actuator.
• Signal circuit shorted to voltage source.
Read More:
SPN 94 - FMI 18 (Fault Code 482)
SPN 1188 - FMI 4 (Fault Code 466)
Blog.Teknisi
0 Response to "SPN 1188 - FMI 3 (Fault Code 465)"
Post a Comment