SPN 3509 - FMI 3 (Fault Code 386)
Friday, July 13, 2018
Fault Codes CUMMINS GTA38 K38 K50 QSK38 QSK50/60 CM850,
Fault Codes CUMMINS Signature ISX QSX15 CM570
SPN3509 FMI3
Sensor Supply 1 Circuit - Voltage Above Normal or Shorted to High Source
CODES:
Fault Code: 386
PID(P), SID(S): S212
SPN: 3509
FMI: 3/3
Lamp: Amber
REASON: High voltage detected at sensor supply number 1 circuit.
EFFECT: Engine power derate.
Circuit Description:
The sensor supply 1 circuit of the engine control module (ECM) provides a 5 volt supply to various sensors on the engine harness. Refer to the wiring diagram for sensor supply identification.
Component Location:
Sensor Supply 1 originates in the Engine Connector portion of the ECM. It supplies 5 volts to sensors in the engine wiring harness.
Conditions for Running the Diagnostics:
This diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.
Conditions for Setting the Fault Codes:
The Engine Control Module (ECM) detected the sensor supply 1 signal voltage was out of range high.
Action Taken When the Fault Code is Active:
• The ECM illuminates the amber CHECK ENGINE lamp and/or the malfunction indicator lamp (MIL) immediately when the diagnostic runs and fails.
• A default value is used for all of the sensors on the sensor supply 1 circuit.
Conditions for Clearing the Fault Code:
• To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
• The fault code status displayed by the recommended Cummins® electronic service tool or equivalent will change to INACTIVE immediately after the diagnostic runs and passes.
• The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
• The “Reset All Faults” command in the recommended Cummins® electronic service tool or equivalent can be used to clear active and inactive faults.
Shop Talk:
• High voltage on the (+) 5 volt supply line can be caused by a short to battery voltage in the engine harness or connectors, or a malfunctioning ECM.
Read More:
SPN 1073 - FMI 11 (Fault Code 392)
SPN 1072 - FMI 11 (Fault Code 388)
Blog.Teknisi
Sensor Supply 1 Circuit - Voltage Above Normal or Shorted to High Source
 |
| Sensor Supply Voltage |
CODES:
Fault Code: 386
PID(P), SID(S): S212
SPN: 3509
FMI: 3/3
Lamp: Amber
REASON: High voltage detected at sensor supply number 1 circuit.
EFFECT: Engine power derate.
Circuit Description:
The sensor supply 1 circuit of the engine control module (ECM) provides a 5 volt supply to various sensors on the engine harness. Refer to the wiring diagram for sensor supply identification.
Component Location:
Sensor Supply 1 originates in the Engine Connector portion of the ECM. It supplies 5 volts to sensors in the engine wiring harness.
Conditions for Running the Diagnostics:
This diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.
Conditions for Setting the Fault Codes:
The Engine Control Module (ECM) detected the sensor supply 1 signal voltage was out of range high.
Action Taken When the Fault Code is Active:
• The ECM illuminates the amber CHECK ENGINE lamp and/or the malfunction indicator lamp (MIL) immediately when the diagnostic runs and fails.
• A default value is used for all of the sensors on the sensor supply 1 circuit.
Conditions for Clearing the Fault Code:
• To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
• The fault code status displayed by the recommended Cummins® electronic service tool or equivalent will change to INACTIVE immediately after the diagnostic runs and passes.
• The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
• The “Reset All Faults” command in the recommended Cummins® electronic service tool or equivalent can be used to clear active and inactive faults.
Shop Talk:
• High voltage on the (+) 5 volt supply line can be caused by a short to battery voltage in the engine harness or connectors, or a malfunctioning ECM.
Read More:
SPN 1073 - FMI 11 (Fault Code 392)
SPN 1072 - FMI 11 (Fault Code 388)
Blog.Teknisi
0 Response to "SPN 3509 - FMI 3 (Fault Code 386)"
Post a Comment