SPN 108 - FMI 4 (Fault Code 222)
Thursday, August 02, 2018
Fault Codes CUMMINS ISB ISBe QSB4.5 QSB5.9 QSB6.7 ISC QSC8.3 ISL ISLe QSL9 CM850 (CM2850)
SPN108 FMI4
Barometric Pressure Sensor Circuit - Voltage Below Normal, or Shorted to Low Source
CODES:
Fault Code: 222
PID(P), SID(S): P108
SPN: 108
FMI: 4/4
Lamp: Amber
REASON: Barometric Pressure Sensor Circuit - Voltage Below Normal, or Shorted to Low Source. Low signal voltage detected at barometric pressure circuit.
EFFECT: Engine power derate.
Circuit Description:
The barometric pressure sensor is used by the electronic control module (ECM) to monitor the barometric pressure. This value is one of many inputs used by the ECM to determine the correct air/fuel ratio for proper engine operation.
Component Location:
The barometric pressure sensor is mounted on the main branch of the engine harness near the ECM.
Shop Talk:
The barometric pressure sensor shares supply and return wires in the engine harness with other sensors. Opens and shorts in the engine harness can cause multiple fault codes to be active. Before troubleshooting Fault Code 222, check for multiple faults.
Possible causes of this fault code include:
• Signal circuit open or shorted to ground in the engine harness or sensor
• Supply line open or shorted to ground.
On-Board Diagnostics (OBD) Information (Euro 4 Certified Engines):
• The ECM illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
• The ECM turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. The MIL lamp and fault code can also be cleared using the INSITE™ service tool.
• The fault code will be cleared from memory after 40 consecutive drive cycles where the diagnostic runs and passes.
On-Board Diagnostics (OBD) Information (Euro 4 Stage 1+ Certified Engines):
• The ECM illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
• An engine torque derate will be activated after 50 hours of engine operation with the fault code active.
• The ECM turns OFF the malfunction indicator lamp (MIL) after 1 ignition cycle that the diagnostic runs and does not fail. The MIL lamp cannot be cleared using the INSITE™ service tool.
• The fault code will be cleared from memory after 400 days or 9600 hours of engine operation.
Read More:
SPN 108 - FMI 3 (Fault Code 221)
SPN 111 - FMI 18 (Fault Code 197)
Blog.Teknisi
Barometric Pressure Sensor Circuit - Voltage Below Normal, or Shorted to Low Source
 |
| Barometric Pressure Sensor Circuit |
CODES:
Fault Code: 222
PID(P), SID(S): P108
SPN: 108
FMI: 4/4
Lamp: Amber
REASON: Barometric Pressure Sensor Circuit - Voltage Below Normal, or Shorted to Low Source. Low signal voltage detected at barometric pressure circuit.
EFFECT: Engine power derate.
Circuit Description:
The barometric pressure sensor is used by the electronic control module (ECM) to monitor the barometric pressure. This value is one of many inputs used by the ECM to determine the correct air/fuel ratio for proper engine operation.
Component Location:
The barometric pressure sensor is mounted on the main branch of the engine harness near the ECM.
Shop Talk:
The barometric pressure sensor shares supply and return wires in the engine harness with other sensors. Opens and shorts in the engine harness can cause multiple fault codes to be active. Before troubleshooting Fault Code 222, check for multiple faults.
Possible causes of this fault code include:
• Signal circuit open or shorted to ground in the engine harness or sensor
• Supply line open or shorted to ground.
On-Board Diagnostics (OBD) Information (Euro 4 Certified Engines):
• The ECM illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
• The ECM turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. The MIL lamp and fault code can also be cleared using the INSITE™ service tool.
• The fault code will be cleared from memory after 40 consecutive drive cycles where the diagnostic runs and passes.
On-Board Diagnostics (OBD) Information (Euro 4 Stage 1+ Certified Engines):
• The ECM illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
• An engine torque derate will be activated after 50 hours of engine operation with the fault code active.
• The ECM turns OFF the malfunction indicator lamp (MIL) after 1 ignition cycle that the diagnostic runs and does not fail. The MIL lamp cannot be cleared using the INSITE™ service tool.
• The fault code will be cleared from memory after 400 days or 9600 hours of engine operation.
Read More:
SPN 108 - FMI 3 (Fault Code 221)
SPN 111 - FMI 18 (Fault Code 197)
Blog.Teknisi
0 Response to "SPN 108 - FMI 4 (Fault Code 222)"
Post a Comment