SPN 1347 - FMI 7 (Fault Code 275)
Friday, August 03, 2018
Fault Codes CUMMINS ISB ISBe QSB4.5 QSB5.9 QSB6.7 ISC QSC8.3 ISL ISLe QSL9 CM850 (CM2850)
SPN1347 FMI7
Fuel Pumping Element Number 1 (Front) - Mechanical System Not Responding Properly or Out of
Adjustment
CODES:
Fault Code: 275
PID(P), SID(S): S126
SPN: 1347
FMI: 7
Lamp: Yellow
REASON: Fuel Pumping Element Number 1 (Front) - Mechanical System Not Responding Properly or Out of Adjustment.
EFFECT: Engine will not run or possible low power.
Circuit Description:
The fuel pump contains two barrel and plunger assemblies; each barrel and plunger assembly utilizes an inlet and outlet check valve. Fuel at gear pump pressure is metered through the fuel pump actuator and unseats one of the two inlet check valves as the fuel at gear pump pressure enters the pumping chamber. As the pumping plunger begins its upward motion, the pressure in the pumping chamber increases rapidly and the inlet check valve is closed. As pressure reaches accumulator pressure, the outlet check valve is opened. As the plunger travels upward, fuel exits past the outlet check valve and pressurizes the fuel rail.
Component Location:
The fuel pump is located on the backside of the gear housing. The barrel and plunger and check valve assemblies are part of the fuel pump head sub-assembly.
Shop Talk:
Fault Code 275 will most likely come active while operating at a steady state loaded condition. At this condition commanded fuel pressures are highest and the pump's pressure balance is affected the most. If a high pressure seal has failed, pump head drain flow will be excessive. If a seal failure has progressed far enough, the engine may not start because of an inability to develop fuel rail pressure.
If the engine will not start, there are two indications that the pump head has failed:
• The drain flow will be excessive. This can be measured while cranking the engine.
• The pumping plungers are broken or mechanically stuck. This can be checked by visual inspection.
A faulty fuel pressure sensor signal due to a damaged fuel pressure sensor signal wire will cause the fuel pressure sensor to be inconsistent. This condition can cause Fault Code 275 to become active on an intermittent basis.
Read More:
SPN 1347 - FMI 4 (Fault Code 271)
SPN 1347 - FMI 3 (Fault Code 272)
Blog.Teknisi
Fuel Pumping Element Number 1 (Front) - Mechanical System Not Responding Properly or Out of
Adjustment
 |
| High Pressure Pump |
CODES:
Fault Code: 275
PID(P), SID(S): S126
SPN: 1347
FMI: 7
Lamp: Yellow
REASON: Fuel Pumping Element Number 1 (Front) - Mechanical System Not Responding Properly or Out of Adjustment.
EFFECT: Engine will not run or possible low power.
Circuit Description:
The fuel pump contains two barrel and plunger assemblies; each barrel and plunger assembly utilizes an inlet and outlet check valve. Fuel at gear pump pressure is metered through the fuel pump actuator and unseats one of the two inlet check valves as the fuel at gear pump pressure enters the pumping chamber. As the pumping plunger begins its upward motion, the pressure in the pumping chamber increases rapidly and the inlet check valve is closed. As pressure reaches accumulator pressure, the outlet check valve is opened. As the plunger travels upward, fuel exits past the outlet check valve and pressurizes the fuel rail.
Component Location:
The fuel pump is located on the backside of the gear housing. The barrel and plunger and check valve assemblies are part of the fuel pump head sub-assembly.
Shop Talk:
Fault Code 275 will most likely come active while operating at a steady state loaded condition. At this condition commanded fuel pressures are highest and the pump's pressure balance is affected the most. If a high pressure seal has failed, pump head drain flow will be excessive. If a seal failure has progressed far enough, the engine may not start because of an inability to develop fuel rail pressure.
If the engine will not start, there are two indications that the pump head has failed:
• The drain flow will be excessive. This can be measured while cranking the engine.
• The pumping plungers are broken or mechanically stuck. This can be checked by visual inspection.
A faulty fuel pressure sensor signal due to a damaged fuel pressure sensor signal wire will cause the fuel pressure sensor to be inconsistent. This condition can cause Fault Code 275 to become active on an intermittent basis.
Read More:
SPN 1347 - FMI 4 (Fault Code 271)
SPN 1347 - FMI 3 (Fault Code 272)
Blog.Teknisi
0 Response to "SPN 1347 - FMI 7 (Fault Code 275)"
Post a Comment